Stock No. 46/06X1/4TC A Self-guided Combination Trimmer.
A 90 Degree Trim Is Obtained By Engaging The Bottom Half.
A 45 Degree Trim Is Obtained By Lowering The Cutter.
A Fine Height Adjuster Is Recommended When Using This Cutter.
A Larger 20mm Bearing Will Spread The Wear Of The Cutting When 45 Degree Trimming.
Dimensions:
D=24 Mm
C=6mm
C2=5mm
C3=6 Mm
B=fractionally Larger Than Cutter Dia
A=90 Degre...More Info
Stock No. 46/6BX1/4TC Cut A Wider Edge Line, At An Angle Of 45 Degrees.
A 16mm Bearing Is Supplied As Standard.
A Larger 19mm Bearing Will Spread The Wear Of The Cutting Edges.
Dimensions:
D=27 Mm
C=9 Mm
A=45 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 27
Cut Length Metric: 9
Angle: 45...More Info
Stock No. 46/6CX1/4TC Cut A Wider Edge Line, At An Angle Of 30 Degrees.
A 16mm Bearing Is Supplied As Standard.
A Larger 19mm Bearing Will Spread The Wear Of The Cutting Edges.
Dimensions:
D=27 Mm
C=7 Mm
A=30 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 27
Cut Length Metric: 7
Angle: 30...More Info
Stock No. 46/6DX1/4TC Cut A Wider Edge Line, At An Angle Of 82 Degrees.
A 16mm Bearing Is Supplied As Standard.
A Larger 19mm Bearing Will Spread The Wear Of The Cutting Edges.
Has A Gap Between The Tips And Bearing, To Reduce Adhesive Build-up.
Dimensions:
D=15 Mm
C=12 Mm
A=82 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 15
Cut Length Metric: 12
Angle: 8...More Info
Stock No. 46/7/50X1/4TC The Glazing Bar Ovolo Cutter Is Bearing Guided To Speed Setting-up And To Enable Curved Frames To Be Moulded.
Dimensions:
D=28 Mm
C=19 Mm
B=12.7 Mm
R=10 Mm
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 28
Cut Length Metric: 19
Bearing Diameter Metric: 12.7...More Info
Stock No. 46/7/60X1/2TC Simultaneously Rounds Over And Profiles The Edge.
Ideal For Pencil Round Architrave.
Dimensions:
D=36 Mm
D2=16 Mm
C=29 Mm
B=16 Mm
R=10 Mm
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Metric: 36
Cut Length Metric: 29
Bearing Diameter Metric: 16...More Info
Stock No. 46/75X1/2TC Self Guiding Classic Cutters With Facility To Change Profile By Fitting Larger Bearing And Varying The Depth. Supplied With Two Bearings.
Dimensions:
D=35 Mm
C=22 Mm
B=9.5 Mm
B2=12.7 Mm
R=6.3 Mm
R2=6.3 Mm
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Metric: 35
Cut Length Metric: 22
Bearing Diameter Metric: 9.5...More Info
Stock No. 46/7X1/4TC Trimming Top And Bottom Surfaces Simultaneously With Bearing Following The Board.
Two Fluted.
Increased Productivity.
Dimensions:
D=18 Mm
C=15mm
C2=9 Mm
A=90 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 18
Cut Length Metric: 15...More Info
Stock No. 47/20X1/4TC For Trimming The Lipping Of Plastic Overlay, And For Rebating And Machining Wood, Duralium And Plastics.
Tungsten Carbide Tipped.
Use At Speed 12000 - 24000 Rpm.
Dimensions:
D=20 Mm
C=13 Mm
A=90 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 20
Cut Length Metric: 13
Angle: 90...More Info
Stock No. 47/20X8MMTC For Trimming The Lipping Of Plastic Overlay, And For Rebating And Machining Wood, Duralium And Plastics.
Tungsten Carbide Tipped.
Use At Speed 12000 - 24000 Rpm.
Dimensions:
D=20 Mm
C=13 Mm
A=90 Degrees
Shank Diameter=8 Mm
Shank Diameter: 8 Mm
Grade: Tct
Diameter Metric: 20
Cut Length Metric: 13
Angle: 90...More Info
Stock No. 47/2X1/4TC For Trimming The Lipping Of Plastic Overlay, And For Rebating And
Machining Wood, Duralium And Plastics.
Tungsten Carbide Tipped.
Use At Speed 12000 - 24000 Rpm.
Dimensions:
D=18 Mm
C=12 Mm
A=90 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 18
Cut Length Metric: 12
Angle: 90...More Info
Stock No. 47/3X1/4TC Three Bevel Cutters For Edging .
For Trimming Laminate, When A Wider Edge Line Is Preferred On The Finished Edge.
Supplied In 80 Degree, 60 Degree And 30 Degree Versions Of Bevel Angle.
No Bottom Cut.
Dimensions:
D=20 Mm
C=14 Mm
A=80 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 20
Cut Length Metric: 14
Angle: 80...More Info
Stock No. 47/40X1/2TC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=30 Mm
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Imperial: 1/2
Diameter Metric: 12.7
Cut Length Metric: 30...More Info
Stock No. 47/45X3/8TC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Dimensions:
D=3/8 Inch
D=9.5 Mm
C=25 Mm
Shank Diameter=3/8 Inch
Shank Diameter: 3/8
Grade: Tct
Diameter Imperial: 3/8
Diameter Metric: 9.5
Cut Length Metric: 25...More Info
Stock No. 47/4X1/4TC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Single Fluted.
Dimensions:
D=1/4 Inch
D=6.3 Mm
C=18 Mm
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 6.3
Cut Length Metric: 18...More Info
Stock No. 47/50SX1/2TC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Specially Designed For The Caravan Building Industry, Used For Cutting Apertures In Windows, Doors & The Floor Pan.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=22.5 Mm
C2=22.5 Mm
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Imperi...More Info
Stock No. 47/50X1/2TC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Will Trim Bottom And Top Laminate
Simultaneously.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=24 Mm
C2=24 Mm
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Imperial: 1/2
Diameter Metric: 12.7
Cut Length Metric: 24...More Info
Stock No. 47/5X1/4TC For Trimming Top & Lip.
Economical Cutters, Perform 3 Functions:
1. To Top Trim The Overlay At 90 Degrees.
2. To Trim The Overlay At 45 Degrees Or 60 Degrees.
3. The Base Of The Cutter Can Trim The Vertical Lipping At 90 Degrees.
Requires Side Fence Or Roller Bearing.
Dimensions:
D=21 Mm
C=6 Mm
A=45 Degrees
A2=90 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct...More Info
Stock No. 47/6AX1/4TC Three Bevel Cutters For Edging .
For Trimming Laminate, When A Wider Edge Line Is Preferred On The Finished Edge.
Supplied In 80 Degree, 60 Degree And 30 Degree Versions Of Bevel Angle.
No Bottom Cut.
Dimensions:
D=24 Mm
C=12 Mm
A=60 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 24
Cut Length Metric: 12
Angle: 60...More Info
Stock No. 47/6CX1/4TC Three Bevel Cutters For Edging .
For Trimming Laminate, When A Wider Edge Line Is Preferred On The Finished Edge.
Supplied In 80 Degree, 60 Degree And 30 Degree Versions Of Bevel Angle.
No Bottom Cut.
Dimensions:
D=24 Mm
C=10 Mm
A=30 Degrees
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Tct
Diameter Metric: 24
Cut Length Metric: 10
Angle: 30...More Info
Stock No. 47/7X1/4TC For Trimming Top & Lip.
Economical Cutters, Perform 3 Functions:
1. To Top Trim The Overlay At 90 Degrees.
2. To Trim The Overlay At 45 Degrees Or 60 Degrees.
3. The Base Of The Cutter Can Trim The Vertical Lipping At 90 Degrees.
Requires Side Fence Or Roller Bearing.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=12.7 Mm
A=60 Degrees
A2=90 Degrees
Shank Diameter=1/4 Inch
Shank Diameter:...More Info
Stock No. 47/8X1/4HSS Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Dimensions:
D=1/4 Inch
D=6.3 Mm
C=16 Mm
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Hss
Diameter Imperial: 1/4
Diameter Metric: 6.3
Cut Length Metric: 16...More Info
Stock No. 765X1/2TC Adjustable Trimmer Will Trim And Bevel The Top And Bottom Edges Of The Workpiece.
The Width Of Workpiece Accommodated Can Be Adjusted With Spacers.
Trimmer Blocks Have Four Wings.
Life Of Cutting Edges Can Be Extended With Larger 26mm Bearing Ref. Bb26.
Dimensions:
D=35.5 Mm
B=22 Mm
A=45 Degrees
Shank Diameter=1/2 Inch
Shank Diameter: 1/2
Grade: Tct
Diameter Metric: 35.5
...More Info
Stock No. S47/4X1/4STC Combination Pierce And Trim Cutters.
Pierce And Cut Out Apertures In Laminate Worktops.
Base Of The Cutter Acting As A Guide Follower.
Single Fluted.
Made From Solid Carbide For Long Life.
Dimensions:
D=1/4 Inch
D=6.3 Mm
C=22 Mm
Shank Diameter=1/4 Inch
Shank Diameter: 1/4
Grade: Stc
Diameter Imperial: 1/4
Diameter Metric: 6.3
Cut Length Metric: 22...More Info
Stock No. S47/70X1/4STC Solid Tungsten Carbide Economy Cutter.
For Use On Short Runs At 90 Degree Or 60 Degree With Ref. S47/70, At 90 Degree Or 83 Degrees With Ref. S47/71 And At 90 Degree Or 45 Degree With Ref. S47/72.
Will Trim And Bevel By Changing Cutter Height.
Requires A Side Fence Or A Copy Follower Guide On The Router.
Dimensions:
D=1/4 Inch
D=6.3 Mm
C=6 Mm
C2=6 Mm
Ol=32 Mm
A=60 Degrees
A2=90 ...More Info
Accessories
